New equipment

MODEL 700SB
MEDIUM DUTY SLIDER BED BELT CONVEYOR
700sb
Conveyor shown with optional supports
Slider bed belt conveyors remain the most popular of all powered conveyors, providing an economical means of transporting goods for packing, testing, inspecting and various assembly line operations.
BELTING: PVC-120 black.
DRIVE PULLEY: 4” dia. with 1-3/16” dia. shaft or 8” dia. with 1-7/16” dia. shaft, both machine crowned and fully lagged.
TAIL PULLEY: 4” dia., machine crowned, with 1-3/16” dia. shaft.
END DRIVE: Allows one-direction (unit) operation; add optional center drive for reversible application.
TAKE-UP: Screw type unit at tail pulley provides 12” belt take-up.
SAFETY POP-OUT ROLLER: Standard on both ends, 1.9” dia. x 16 ga. steel roller, model 196S.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
BED: 7” x 1-1/2” x 12 ga. channel frame with 14 ga. slider bed.
BELT SPEED: 60 FPM, constant.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
RETURN ROLLERS: 1.9” dia. x 16 ga. steel, model 196S, adjustable.
ELECTRICAL CONTROLS: Optional.

CONVEYORS PRICES

OPTIONAL SUPPORTS

OPTIONAL SPEEDS

SPECIAL NOTE: ADD 20% STEEL SURCHARGE TO ALL PRICES

MODEL 796RB
MEDIUM DUTY ROLLER BED BELT CONVEYOR
796rb
Model 796RB, medium duty roller bed belt conveyor, is well suited for transporting unit loads with lesser horsepower requirements than slider bed belt conveyors.
BELTING: PVC-120 black. CARRIER ROLLERS: 1.9” dia. x 16 ga. steel rollers, model 196S.
DRIVE PULLEY: 4” dia. with 1-3/16” dia. shaft or 8” dia. with 1-7/16” dia. shaft, both machine crowned and fully lagged.
TAIL PULLEY: 4” dia., machine crowned, with 1-3/16” dia. shaft.
END DRIVE: Allows one-direction (unit) operation; add optional center drive for reversible application.
SAFETY POP-OUT ROLLER: Standard on both ends, 1.9” dia. x 16 ga. steel roller, model 196S.
SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30’.
BED: 7” x 1-1/2” x 12 ga. channel frame. Bed sections attached with couplings and floor supports.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
TAKE-UP: Screw type unit at tail pulley provides 12” belt take-up.
BELT SPEED: 60 FPM, constant.
RETURN ROLLERS: 1.9” dia. x 16 ga. steel, model 196S, adjustable.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ELECTRICAL CONTROLS: Optional.

CONVEYORS PRICES

OPTIONAL SUPPORTS

OPTIONAL SPEEDS

SPECIAL NOTE: ADD 20% STEEL SURCHARGE TO ALL PRICES

MODEL 796RBF
ROLLER BED INCLINED FLOOR-TO-FLOOR BELT CONVEYOR

Model 796RBF floor-to-floor conveyor provides higher load capacity, reversible flow and nose-over allows for simple adjustments for inclines 0-35°. Shown with optional supports, knee braces,
chain driven feeder and right hand drive. All units furnished standard with left hand drive.

BELTING: Black PVC ruff-top.
CARRIER ROLLERS: 1.9” dia. X 16 ga. steel, model 196S.
DRIVE PULLEY: 8” dia. with 1-7/16” dia. shaft, both machine crowned and fully lagged.
TAIL PULLEY: 4” dia., machine crowned, with 1-3/16” dia. shaft.
RETURN ROLLERS: 1.9” dia. x 16 ga. steel, model 196S, adjustable.
CENTER DRIVE: Reversible drive with 24” integral belt take-up.
SAFETY POP-OUT ROLLER: Standard on both ends, 1.9” dia. x 16 ga. steel roller, model 196S.
BELT SPEED: 60 FPM, constant.
BED: 7” x 1-1/2” x 12 ga. channel frame. Bed sections attached with couplings and floor supports.
NOSE-OVER: Provides smooth transition from incline to horizontal position. Single nose-over adjusts 0-20°; double nose-over adjusts 0-35° (specify single or double).
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
FLOOR SUPPORTS: Optional.
ELECTRICAL CONTROLS: Optional.

CONVEYORS PRICES

OPTIONAL SUPPORTS

OPTIONAL SPEEDS

SPECIAL NOTE: ADD 20% STEEL SURCHARGE TO ALL PRICES

MODEL 196LRC
MEDIUM DUTY BELT DRIVEN LIVE ROLLER CURVE
Roach model 196LRC features tapered rollers to maintain product orientation. Reversible, it is also commonly slave driven from 196VP and 796CALR conveyors
TREAD ROLLERS: 2-1/2” dia. to 1- 11/16” dia. x 14 ga. steel tapered rollers, model 254T; 1.9” dia. x 16 ga. steel straight tangent rollers, model 196S.
PRESSURE SHEAVES: Provides drive belt pressure to upper tread rollers.
BELT: “B” section V-belt.
TAKE-UP: Screw type adjustable sheaves provided to maintain belt tension.
TANGENTS: 1’-0” both ends on 90°; 1’-6” both ends on 45°; 1’-0” both ends on 180°. Tangent roller centers provided on 3” RC.
SPEED: 60 FPM, constant.
BED: 7” x 1-1/2” x 12 ga. formed steel channel frame.
BEARINGS: End shafts are supported by precision, heavy duty, lubricated, ball bearing units with cast iron housings.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain.
DRIVE LOCATION: Drive located on outside of curve. Specify left hand tangent length, right hand tangent length and drive location (“left hand drive” or “right hand drive”).
NOTE: Drive hand determined with reference point located at outside of curve. For models slave driven (less drive), specify drive shaft location.
CAPACITY: 500 lb. total distributed live load.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor, located at infeed end of curve below bed on 45° and 90° curves; 3/4 HP supplied on all 180° curves.
SPECIAL WIDTHS: Consult factory for pricing of ALL widths not shown.
ELECTRICAL CONTROLS: Optional

CONVEYORS PRICES

OPTIONAL SUPPORTS

OPTIONAL SPEEDS

SPECIAL NOTE: ADD 20% STEEL SURCHARGE TO ALL PRICES

MODEL 796CALR
MEDIUM DUTY CAM ADJUSTED LIVE ROLLER
Roach 796CALR is ideally suited for side loading, unloading or temporary accumulation. Its unique cam allows tread roller drive pressure to be adjusted in only seconds.
READ ROLLERS: 1.9” dia. x 16 ga. steel rollers, model 196S.
PRESSURE ROLLERS: 1.9” dia. x 16 ga. steel, model 196S, cam adjustable.
BELTING: 6” wide black PVC-120 COS.
CENTER DRIVE: Reversible drive with 24” integral belt take-up. For units under 8’-0” overall length, drive components must be stacked. Consult factory for minimum unit elevation.
SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30’.
DRIVE PULLEY: 4” dia. with 1-3/16” dia. shaft or 8” dia. with 1-7/16” dia. shaft, both crowned and fully lagged.
END PULLEY: 4” dia., crowned, with 1-3/16” dia. shaft.
RETURN ROLLERS: 1.9” dia. x 16 ga. steel, model 196S, adjustable.
BED: 7” x 1-1/2” x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7’-0” elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
SPEED: 60 FPM, constant. ELECTRICAL CONTROLS: Optional.

CONVEYORS PRICES

OPTIONAL SUPPORTS

OPTIONAL SPEEDS

SPECIAL NOTE: ADD 20% STEEL SURCHARGE TO ALL PRICES

MODEL 196G
1.9” DIA. X 16 GA. GALVANIZED STEEL GRAVITY ROLLER CONV.
STRAIGHT SECTION MODEL NUMBER
196S-13-6-L-6 196S-(between frames)-(roller centers)- (set high or low)-(length
ROLLERS: 1.9” x 16 ga. steel tubing, model 196S, with smooth swaged ends.
FRAMES: Formed steel painted channel 3-1/2” x 1-1/2” x 10 ga. set high; 4-1/2” x 1-1/2” x 10 ga. set low.
BEARINGS: Integral plain ball bearings, zinc plated, grease packed.
FRAME CAPACITY: 250 lbs. per roller, or 1300 lbs. maximum distributed live load per 10’ section with supports at 10’ centers; 3200 lbs. at 5’ centers.
COUPLINGS: Butt type. AXLES: 7/16” hex shaft, spring loaded. OPTIONAL FRAME: 4” @ 5.4 lbs. struc. steel channel frame, rollers 3/16” high, may vary due to structural tolerances.

CONVEYORS PRICES

OPTIONAL SUPPORTS

SPECIAL NOTE: ADD 20% STEEL SURCHARGE TO ALL PRICES

MODEL 196GC
1.9” DIA. X 16 GA. GALVANIZED STEEL GRAVITY ROLLER CONV.
CURVED SECTION MODEL NUMBER 196SC-21-H-45
196SC-(between frames)-(set high or low)-(degree)
ROLLERS: 1.9” x 16 ga. steel tubing, model 196S, with smooth swaged ends.
FRAMES: Formed steel painted channel 3-1/2” x 1-1/2” x 10 ga. set high; 4-1/2” x 1-1/2” x 10 ga. set low.
BEARINGS: Integral plain ball bearings, zinc plated, grease packed.
FRAME CAPACITY: 250 lbs. per roller, or 1300 lbs. maximum distributed live load per 10’ section with supports at 10’ centers; 3200 lbs. at 5’ centers.
COUPLINGS: Butt type. AXLES: 7/16” hex shaft, spring loaded. OPTIONAL FRAME: 4” @ 5.4 lbs. struc. steel channel frame, rollers 3/16” high, may vary due to structural tolerances.

CONVEYORS PRICES

OPTIONAL SUPPORTS

SPECIAL NOTE: ADD 20% STEEL SURCHARGE TO ALL PRICES